Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
We have noticed this great article involving A Step-by-Step Guide to Installing a Bathtub below on the web and figured it made good sense to discuss it with you in this article.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new tub in your washroom if you have actually currently gotten a brand-new tub as well as don't need to change the setup of your previous supply of water pipes.
Your tools as well as material checklist must make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wood boards under its feet, place the tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the tub has actually been utilized a minimum of once as this will settle it into its final position.
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom ought to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bathroom and the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I was made aware of that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on our other web page. Please take a moment to share this write-up if you enjoyed it. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request Service Report this page